Fence panels can be attached to a brick wall for various reasons. It can be used to add a decorative element to a building or to provide additional security. It can also enhance the appearance of a garden area by serving as a backdrop for plants and flowers.
Whatever your motivation, there are a few things you should be aware of before you begin.
Anyone wishing to put fence or gate posts against a brick wall or into concrete should try this easy DIY. This technique can also secure decking joists or other things against concrete or brick. These bolts are versatile as long as you put them in concrete or brick. So, let’s start discussing the whole process, including a few considerations.
Table of Contents
Needed Tools To Fix Wooden Fence Post
- Hammer
- Electric drill
- Masonry drill bits
- Fence posts
- Ratchet posts
- Shims
- Clout nails
Steps To Fix The Wooden Fence Post To The Brick Wall
The simplest of the gate posts to install, and they’re made of the same material as your gates. So, everything matches. They’re used to secure a gate to a wall or other structure, and they’re secured using either frame fixings or masonry screws and bolts.
Drilling
You’ll need a drill bit that matches the diameter of your bolts. We used 10mm bolts for our fence posts, which required a drill bit. Make sure you’re using a wood drill bit for this project, and start by drilling two or three holes evenly spaced into your fence post.
We only required two because we just have a low-level brick wall. Hold the wood against the wall and use a spirit level to ensure it’s straight. Mark the same holes on the brickwork behind you while keeping it in place. Drilling two very small pilot holes through the hole in your fence post are the easiest way to do this.
Drill the hole once it’s been marked, making sure it’s deep enough for the bolt to be inserted into. If you don’t have one, you’ll need a hammer drill for this or a drill with a hammer mode and a masonry drill bit.
Use A Cleaning Brush To Remove The Dust
You’ll need to clean out the dust from the back of the hole once it’s been drilled. You can get the bulk out by moving your drill back and forth. We also have a small hole-cleaning brush that comes in handy.
Wrap a piece of the damp-proof membrane around the bottom of each fence post. You can extend the life of your fence post by protecting the base from water in the ground if it is sat slightly in the ground.
This was accomplished by placing a sheet of damp-proof membrane over the base of the fence post. To keep everything together, use galvanized clout nails.
Use Fence Post Brackets
When mounting fence panels to a brick wall, wood fence post brackets are an excellent choice. Brackets are one of the most secure and rigid ways to secure fence posts. Galvanized fence brackets are preferred because they are more rust and corrosion-resistant.
Mark the position of your fence posts with brackets in the same manner as explained previously. Then, using a bracket as a template, mark where you need to drill on the masonry. Use the recommended fasteners to secure the brackets. Attaching the fence posts to the brackets is the final step.
Attach The Concrete Bolts
Reposition your fence post against the brickwork and secure it with a concrete bolt that runs through the fence post and into the wall. To do this, you’ll need a ratchet set, and be careful not to overtighten your bolts. If your wall isn’t completely straight, you can use packing shims behind the post to bring it forward as needed.
The concrete base of a brick wall will make it difficult to sink fence posts into the earth. As a result, you’ll need to secure your fence posts to the wall. Using your fence panels as a guide, work out where your fence posts should go.
Make sure they’re vertical using a spirit level before marking their location on the wall. Make sure they aren’t touching the ground to avoid absorbing wet. It’s also a good idea to use a preservative on the back of your fence posts. This will assist in preventing moisture absorption where the post meets the brickwork.
Use A Metal Base For The Concrete Floor
These fixings are also great for installing a fence post on a concrete floor. Why not use metal bases and affix them to the concrete floor to save yourself the trouble of digging it up? If your floor is level, simply mark the four holes you’ll need on the floor, drill them out and screw them in. After that, you may place your fence post and call it a day.
That’s all there is to it! These bolts can be used for a variety of applications. They’re quick and simple to use, and they appear to be very strong and durable so far.
Conclusion
After the fence posts are in place, you can start putting the fence together. The method you use will be primarily determined by the type of fence you select. If you use frame fixings, the installation method is very similar to what is described above.
When drilling and installing the gate post, you must first drill all of the holes in the brickwork and then insert the plugs or sleeves before repositioning the gate post and drilling the fixings into the plugs and sleeves.
