LED light strips are widely used for indoor and outdoor home lighting. The straightforward design makes enhancing a space simple. Thanks to their backing, the lights are easy to install and look great around your stereo setup. Your LED light strips might occasionally need to be moved, however.
You might move to a new place or need to move the lights. It can be difficult to take LED light strips off of your wall. It can be a quick and simple process with the appropriate equipment and guidance.
This article will demonstrate how to remove LED light strips from a wall in just a few easy steps. To learn more about how to remove LED light strips, continue reading.
Table of Contents
Can LED Strip Lights Damage Walls During Their Removal?
It fully depends on the manufacturing process, but for the most part, LED strips won’t harm your wall paint. The cheap adhesives used on the strips may also tear off the paint when the strips are removed. If you reside in a leased home, this may be very challenging.
Because you altered the wall paint, your landlord might charge you. In other words, high-quality LED strip lights won’t scuff up the walls. If the adhesives on the back of the light strip are failing, you want to replace your light strips because you don’t like where they’re installed, or they’re in bad shape.
Whatever the cause, resticking LEDs is the same as when they were first installed. It won’t take as long because you’re just repeating what has already been done.
Steps To Get LED Lights Strips Off The Wall
Prepare The Area
Purchase the appropriate screwdriver. Get gloves to shield your hands from the LED strip’s jagged edges. Multiple layers, including one composed of metal, make up LED strips. While removing the light strips from the walls, the metal layer may sting your fingers if it makes touches them.
Shut Off The Lights Before Removal
It is forbidden to use any electrical device while plugged in, so never do so. As you work on the LED Strip Light, turn off the main power source so that no current flows through it. The performance of your strips will be harmed by water damage if the liquid touches your LEDs.
So, take care to prevent this from happening. Before adding a layer of double-sided tape, rubbing alcohol, cleaning the surface, and re-sticking the LED in a different location, let the backs of your LEDs dry.
Check Walls For Any Stuck LED Lights
If the wall covering has been removed with steam. If you cannot accomplish this, you can pay someone to steam it. Your task will be easier because it is now possible to see where the LED light strips are attached, thanks to the steam-off wallpaper.
If there are any cables stopping you from completing your task securely, cut them with a sharp razor or blade.
Peel Off Borders With A Plier
Locate all border and trimming strips that have adhesive on the wall hidden behind them. These border pieces need to be reused, so take care not to damage them too much when removing them with pliers.
With this method, you will achieve clean cuts, making a lovely finish when painting the walls again.
Remove Each LED Light Strip Individually
Remove the plug from the outlet or, in the case of hardwired light strips, pull the switch down to turn off the main power supply. When working with electricity, this will protect you from electric shock. For your safety and the safety of the LED strip, it is not advised to operate on any electrical equipment while it is connected.
This will assist with led light strip removal from walls. Use a knife or other sharp object to cut through any cables connecting each LED light strip part so that they are all no longer connected.
When cutting, take care not to go too deep since this could harm the individual LEDs in each location, rendering certain parts useless once the wall has been removed.
Each LED light strip’s edge should be grasped with both hands and pulled slowly and carefully. Work your way from one end to the other to remove the whole part from the wall. If a section is difficult to remove, push down gently but firmly on either side of it with a flat head screwdriver before pulling it off as you did with other sections.
Disconnect All Remaining Cables
After severing the connections between each strip, cut any remaining wires with a blade or knife to prevent them from re-connecting once the wall cavity has been opened. With a sharp blade, cut the glue. It depends on the type of glue and how you should cut the adhesive.
If hot glue was used, you might use a blade to remove any debris, then clean it with a wet towel and dry it with a hairdryer or fan heater. Peel off any remaining glue after using the double-sided tape if it was used.
Replace any damaged LED light components with new ones using the same connector type if you discover they were damaged due to frequent plugging. If the claim is invalid, you should repair the damage or gap on your led light strip for future use by covering it with electrical tape or another suitable material.
Bottom Line
LED strips are ideal for enhancing the ambiance of your home and illuminating drab spaces. Don’t hurry things along if you don’t want to risk damaging the wall.
Before you install your LED strips where you want them, you can perform a patch test. Check to see whether the paint peels off now by slowly pulling it off. In that case, you can install your LED strip light without worrying.
Furthermore, we advise tidying up any messes during installation and gathering all the utilized tools and supplies. Take good care of your LED lights because they can be expensive to replace if they fail or become damaged.
