How To Remove Clip Lock Roofing

How To Remove Clip Lock Roofing

Clip lock roofs are ideal for cladding since they are cost-effective, long-lasting, and secure. Regular care, on the other hand, assures that these roofs will last for many years.

As a result, removing clip locks is an essential part of roof maintenance. The clips must be lifted from below with a pinch bar or the claw end to remove clip locks from roof sheets.

However, you must first pry out the top sheet using a flat head screwdriver. To get started, all you’ll need is a flat head screwdriver, one claw hammer, a pinch bar, a single piece of wood, and some essential safety gear.

In this post, we’ll go over why it’s so important to make sure your clip-lock roof is placed correctly, as well as how to spot any issues before they become too difficult to fix.

The Working Process Of Clip Locks

Clip-lock roof sheets are made for flat roofs with an incline of 0 to 1 degree. Unlike standard metal roof sheets, these roof sheets are attached by clips from below rather than screws from above.

Doesn’t it sound cool? In comparison to standard screw-fix roofs, Clip-lock roofs have concealed fasteners that provide more excellent water tightness. Consider this: every screw that secures a roof is a potential source of leakage and corrosion over time.

A variety of companies manufactures these sheets. In early times, clip locks roofs were widespread on residences and commercial structures. They have, however, recently enjoyed a return in popularity. These sheets are formed up of ribs and pans.

There are basically two types of clip locks that are available in the markets. On the other hand, Clip locks are similar in terms of installation, maintenance, and removal. We will cover the clip lock removal process step by step in this article. So, you can comprehend it and remove the clip lock from your roof after reading it.

1) Safety Is The First Thing To Consider

First and foremost, you must secure yourself before ascending to the roof. This is necessary since removing the clip locks from the roofing will need a significant amount of time on the roof. Personal protection equipment should be worn from now on.

Additionally, climb to the roof using a sturdy ladder. To keep the ladder from slipping, employ a ladder anchor safety stabilizer. Above all, always wear the highest-quality safety equipment. These will ensure your safety while also improving your self-assurance. However, if you’re working in direct sunshine, take care of your skin with sunscreen.

2) Treat The Upper Sheet With Tools

To remove clip locks, you’ll need a flat-head screwdriver, a claw hammer, a pinch bar, and a piece of wood bar. To begin, you must first climb onto the roof while adhering to all safety precautions. The sheet, usually the upper sheet covering the sheet beneath, is attached to a metal framing with clip lock points and can be found on the roof.

Then, using a flat-end screwdriver, reach in close to the end of the sheet and gently pry out the upper sheet. As a result, you can create a space between the sheets.

3) Uplift The Upper Sheet

Lift the upper sheet from the gap you’ve created. As a result, a pinch bar with a woodblock is required. The sheet would not be damaged because of the woodblock. Additionally, try to grasp the upper sheet by putting the pinch bar beneath the space between sheets.

Push the pinch bar upward to pull the upper sheet even higher. Using your fingers, pull back the upper sheet. Don’t put your fingers here until the pinch bar has opened a proper gap. If you haven’t done so already, consider donning gloves.

4) Remove The Clip Locks

Carry on until all of the clip locks on the roof have been removed. When the pinch bar fails, use the claw hammer; it is always preferable to use the pinch bar and fingers together. To remove the locks, permanently remove them in sequential order. The sheet could be destroyed if you break the serial.

The sheet will unclip as you roll it backward. Thus, the clip locks must be removed. But don’t overdo it. Otherwise, the sheet could be harmed or even broken.

Compared to a pitched metal roof, every hole in a clip lock roof allows water to enter more quickly. As a result, drilling and utilizing screws on a patch repair or installation will make the roof extremely vulnerable to leaks. When exposed to water, the regions around the screws will rust as well. When a property is close to the sea, this might be especially dangerous.

Solar panels can be mounted using specialized mounting brackets, so no holes in the sheeting are required. There’s no reason to leave exposed screws on a clip lock roof if you’re doing repairs. Instead, it would help if you utilized fixing clips.

Final verdict

Clip lock sheets are now composed of a lighter, softer metal that is simpler to roll form than in the past when they were made of. Things were done with 6 mm thick steel. When trodden on, today’s weaker metals are considerably more easily damaged.

As a result, if you stand on the part of the roof that isn’t supported by a purlin, the roofing sheets will stretch and bow.

The roofing clip lock removal procedure has been discussed. You should now be able to remove clip lock roofing. While standing or sitting on a panel, carefully remove the clip locks. While removing all clip locks from the roofing, always stand or sit on an adjacent panel.

You can follow the discussed steps and points while removing clip locks from the roofing.

Also read: What Is Roof Repointing

Also read: How To Fix A Lawn Full Of Weeds

Related Posts